Routing Information Protocol RIP
In
this article I will demonstrate an example of Rip Routingconfigurations.
We will use four different series router so you can get familiar with all different platform covered in CCNA exam. Create a topology as shown in
figure.
IP
RIP comes in two different versions: 1 and 2. Version 1 is a distance vector
protocol and is defined in RFC 1058. Version 2 is a hybrid protocol and is
defined in RFCs 1721 and 1722. The CCNA exam now primarily focuses on version
2. There are no major differences between RIPv1 or RIPv2 so far configurations
concern. To read more about differences between RIPv1 or RIPv2 or know about
the characteristics read our pervious article about RIP.
|
|
||||||||||||||||||||||||
|
|
||||||||||||||||||||||||
|
|
||||||||||||||||||||||||
To configure any router double click on it and
select CLI. To configure this topology use this step by step
guide.
(1841Router0)
Hostname R1
To configure and enable rip routing on R1 follow
these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#interface fastethernet 0/0
R1(config-if)#ip address 10.0.0.1 255.0.0.0
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
R1(config-if)#exit
R1(config)#interface serial 0/0/0
R1(config-if)#ip address 20.0.0.1 255.0.0.0
R1(config-if)#clock rate 64000
R1(config-if)#bandwidth 64
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to
down
R1(config-if)#exit
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R1(config)#router rip
R1(config-router)#network 10.0.0.0
R1(config-router)#network 20.0.0.0
R1(config-router)#exit
R1(config)#
(2620XM-Router1)
Hostname R2
To configure and enable rip routing on R2 follow
these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#interface serial 0/0
R2(config-if)#ip address 20.0.0.2 255.0.0.0
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0,
changed state to up
R2(config-if)#exit
R2(config)#interface fastethernet 0/0
R2(config-if)#ip address 30.0.0.1 255.0.0.0
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
R2(config-if)#exit
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
R2(config)#router rip
R2(config-router)#network 20.0.0.0
R2(config-router)#network 30.0.0.0
R2(config-router)#exit
R2(config)#
(2620XM-Router2)Hostname
R3
To configure and enable rip routing on R3 follow
these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3
R3(config)#interface fastethernet 0/0
R3(config-if)#ip address 30.0.0.2 255.0.0.0
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
R3(config-if)#interface serial 0/0
R3(config-if)#ip address 40.0.0.1 255.0.0.0
R3(config-if)#clock rate 64000
R3(config-if)#bandwidth 64
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
R3(config-if)#exit
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0,
changed state to up
R3(config)#router rip
R3(config-router)#network 30.0.0.0
R3(config-router)#network 40.0.0.0
R3(config-router)#exit
R3(config)#
(2811Router3)
Hostname R4
To configure and enable rip routing on R4 follow
these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/0/0
Router(config-if)#ip address 40.0.0.2 255.0.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0,
changed state to up
Router(config-if)#exit
Router(config)#interface fastethernet 0/0
Router(config-if)#ip address 50.0.0.1 255.0.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#exit
R4(config)#router rip
R4(config-router)#network 40.0.0.0
R4(config-router)#network 50.0.0.0
R4(config-router)#exit
R4(config)#
PC-1
PC>ipconfig
IP Address......................: 10.0.0.2
Subnet Mask.....................: 255.0.0.0
Default Gateway.................: 10.0.0.1
PC>ping 50.0.0.2
Pinging 50.0.0.2 with 32 bytes of data:
Reply from 50.0.0.2: bytes=32 time=156ms TTL=124
Reply from 50.0.0.2: bytes=32 time=127ms TTL=124
Reply from 50.0.0.2: bytes=32 time=156ms TTL=124
Reply from 50.0.0.2: bytes=32 time=140ms TTL=124
Ping statistics for 50.0.0.2:
Packets: Sent = 4,
Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 127ms,
Maximum = 156ms, Average = 144ms
PC>
PC-2
PC>ipconfig
IP Address......................: 50.0.0.2
Subnet Mask.....................: 255.0.0.0
Default Gateway.................: 50.0.0.1
PC>ping 10.0.0.2
Pinging 10.0.0.2 with 32 bytes of data:
Reply from 10.0.0.2: bytes=32 time=140ms TTL=124
Reply from 10.0.0.2: bytes=32 time=141ms TTL=124
Reply from 10.0.0.2: bytes=32 time=157ms TTL=124
Reply from 10.0.0.2: bytes=32 time=156ms TTL=124
Ping statistics for 10.0.0.2:
Packets: Sent = 4,
Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 140ms,
Maximum = 157ms, Average = 148ms
You can verify that RIP is running successfully via show
ip protocols command in privilege mode.
R1#show ip protocols
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 2 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 1, receive any version
Interface Send Recv
Triggered RIP Key-chain
FastEthernet0/0 1
2 1
Serial0/0/0 1
2 1
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
10.0.0.0
20.0.0.0
Passive Interface(s):
Routing Information Sources:
Gateway Distance Last Update
20.0.0.2 120 00:00:20
Distance: (default is 120)
R1#
You can use show ip route command to troubleshoot
rip network. If you did not see information about any route
checks the router attached with that network.
R1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP
D - EIGRP, EX -
EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA
external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF
external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 -
IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate
default, U - per-user static route, o - ODR
P - periodic
downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is
directly connected, FastEthernet0/0
C 20.0.0.0/8 is
directly connected, Serial0/0/0
R 30.0.0.0/8
[120/1] via 20.0.0.2, 00:00:01, Serial0/0/0
R 40.0.0.0/8
[120/2] via 20.0.0.2, 00:00:01, Serial0/0/0
R 50.0.0.0/8
[120/3] via 20.0.0.2, 00:00:01, Serial0/0/0
R1#
To
test rip routing do ping from pc1 to pc2 and vice versa. If you get replay then
you have successfully configured rip routing but if you did not get replay
double check this configuration and try to troubleshoot. I have
uploaded a configured and tested topology in case you are unable to locate the
problem spot then download this configuration file. And try to find out where have
you committed mistake
rip
routing configurations
|
Commands
|
Descriptions
|
|
Router(config)#router
rip
|
Enables
RIP as a routing protocol
|
|
Router(config-router)#network
w.x.y.z
|
w.x.y.z
is the network number of the directly connected network you want to
advertise.
|
|
Router(config)#no
router rip
|
Turns
off the RIP routing process
|
|
Router(config-router)#no
network w.x.y.z
|
Removes
network w.x.y.z from the RIP routing process.
|
|
Router(config-router)#version
2
|
RIP
will now send and receive RIPv2 packets globally.
|
|
Router(config-router)#version
1
|
RIP
will now send and receive RIPv1 packets only
|
|
Router(config-router)#no
auto-summary
|
RIPv2
summarizes networks at the classful boundary. This command turns
autosummarization off.
|
|
Router(config-router)#passive-interface
s0/0/0
|
RIP
updates will not be sent out this interface.
|
|
Router(config-router)#no
ip split-horizon
|
Turns
off split horizon (on by default).
|
|
Router(config-router)#ip
split-horizon
|
Re-enables
split horizon
|
|
Router(config-router)#timers
basic 30 90 180 270 360
|
Changes
timers in RIP: 30 = Update timer (in seconds) 90 = Invalid timer (in seconds)
180 = Hold-down timer (in seconds) 270 = Flush timer (in seconds) 360 = Sleep
time (in milliseconds)
|
|
Router#debug
ip rip
|
Displays
all RIP activity in real time
|
|
Router#show
ip rip database
|
Displays
contents of the RIP database
|

No comments:
Post a Comment